MODIFICATION AND PERFORMANCE EVALUATION OF IAR GROUNDNUT SHELLER FOR SOME SELECTED VARIETIES OF PULSES

TABLE OF CONTENTS
Title Page
Abstract
Table of Contents
Glossary

CHAPTER ONE
1.0 INTRODUCTION
1.1 General Background
1.2 Statement of the Problems
1.3 Justification
1.4 Aim and Objectives of the study

CHAPTER TWO
2.0 LITERATURE REVIEW
2.1 Review of Related Works
2.2 Machine and Operation Factors
2.3 Institutes for Agricultural Research (IAR) Groundnut Sheller
2.4 Groundnut Shelling Methods
2.4.1 Manual shelling methods
2.4.2 Mechanized shelling method

CHAPTER THREE
3.0       MATERIALS AND METHODS
3.1       Description of the Modified Machine
3.2       Design Consideration
3.3       Material Selection
3.4       Methods
3.4.1 Experimental procedure
3.4.2 Determination of design related properties
3.4.3 Determination of size of the components
3.4.4 Machines performance evaluation
3.4.5 Experimental design and analysis

CHAPTER FOUR
4.0 RESULTS AND DISCUSSION
4.1       Design Related Properties
4.1.1 Basic geometric properties of the crops
4.1.2 Complex geometric properties of the crops
4.1.3 Some mechanical properties of the crops
4.2       Effect of Cylinder Speed, Feed Rate and Concave to Cylinder Clearance of the Machine Performance
4.2.1Effects of cylinder speed on shelling efficiency at various feed rates
4.2.2 Effects of cylinder speed on shelling efficiency at various concave clearances
4.2.3Effects of cylinder speed on cleaning efficiency at various feed rates
4.2.4 Effects of cylinder speed on cleaning efficiency at various concave clearances
4.2.5Effect of cylinder speed on grain damage at various feed rates
4.2.6Effect of cylinder speed on grain damage at various concave clearances
4.2.7Effect of cylinder speed on scatter loss at various feed rates
4.2.8Effect of cylinder speed on scatter loss at various concave clearances
4.2.9Effect of cylinder speed on output capacity at various feed rates
4.2.10 Effect of cylinder speed on output capacity at various concave clearances
4.2.11Best performance parameters for the modified machine
4.3 Comparative Performance of Modified and IAR Groundnut Shelling Machines.
4.3.1 Comparative shelling performance of the machines
4.3.2 Comparative cleaning performance of the machines
4.3.3 Comparative machinery grain damages
4.3.4 Comparative machinery scattered loss
4.3.5 Comparative output capacity of the machines

CHAPTER FIVE
5.0 SUMMARY, CONCLUSION AND RECOMMENDATIONS
5.1 Summary
5.2 Conclusion
5.3Recommendations
REFERENCES
APPENDICES


ABSTRACT
IAR groundnut sheller was developed in 1985 and the design was based on the properties of the then groundnut variety known as Ex-Dakar. New varieties were later developed whose acceptability in practice override, this called for its modification and determination of the characteristics of new varieties.The machine size was modified resulting in the modification of all its components for pulse shelling. The machine consists of the hopper, shelling cylinder, removable concave, blower, chaffs outlet, grains delivery chute, clearance adjuster and frame. The machineperformance was comparatively evaluated using groundnut and cowpea as test crops. A combination of four cylinder speed levels; 2.59, 2.79, 2.98 and 3.18 m/s (130, 140, 150 and 160 rpm), three feed rates (8, 10, and 12 kg/min) and three concave clearances (19, 21 and 23 mm) were used for the performance evaluation of themodified shelling machine using groundnut while a combination of three speed levels; 2.39, 2.59, and 2.79 m/s (120, 130 and 140 rpm) and three feed rates (12, 15 and 18 kg/min) were used for cowpea crop. The results were analyzed statistically in a completely randomized block design. Least Significant Difference (LSD) method was employed to assess the effect of parameter levels while a t-test was used to assess the differences in the machines performance. The basic geometric, complex geometric, and some mechanical properties of four selected varieties each of groundnut and cowpea were determined. The optimum performance of the developed machine using groundnut was found at a speed of 3.18 m/s (160 rpm) with a feed rate of 8 kg/min and 21 mm concave clearance. These resulted in shelling efficiency, cleaning efficiency, scatter loss, damaged grains and output capacity of 94.90%, 97.22 %, 6.29 %, 14.00 % and 254.99 kg/h respectively. When evaluated with a cowpea, the optimum performance was found at a speed of 2.79 m/s (140 rpm) with a feed rate of 12 kg/min and 10 mm concave to cylinder

clearance. These resulted in shelling efficiency, cleaning efficiency, scatter loss, damaged grains and output capacity of 93.24 %, 98.31 %, 0.625 %, 0.00 % and 546.18 kg/h respectively. The levels of the independent variables were found to have highly significant differences with most of the performance indices for groundnut shelling but otherwise for cowpea. Generally, the output capacity of the modified machine was superior over that of the existing machine while its performance on cowpea was superior over that of the groundnut.


CHAPTER ONE
1.0       INTRODUCTION
1.1       General Backgrounds
Pulses are annual leguminous crops yielding grains or seeds used for food, feed and sowing purposes. Pulses are crops yielding from one to twelve seeds of variable size, shape, and colour within a pod. In addition to their values as food and feed stuffs, pulses are also important in cropping systems for their ability to produce nitrogen and thus increase the fertility of the soil (FAO, 2011). Included in the pulses are groundnut and cowpea.Groundnut (Arachis hypogaea L.) also known as peanut,is a member of the family papilionaceae, the largest and most important of the three divisions of leguminasae (Alonge and Adegbulugbe, 2005).The groundnut seed composed of approximately equal weight of fatty and none fatty oil; the relative amount of each depends upon its variety and maturity (Young, and Ahmed,

1982). It is one of the world‟s most popular crops cultivated throughout the tropical and sub-tropical areas where annual precipitation is between 1000 – 1200mm for optimum growth of the crop.Groundnut is the 13th most important food crop of the world (John, 2010). It is the world‟s 4th most important source of edible oil and 3rd most important source of vegetable protein (Taru et al., 2008). The crop is native to South America, Mexico, and Central America. It was first cultivated in a valley in Peru. The leading world producers of the crop are China, India, Nigeria, USA, and Senegal. Nigeria ranks third among the major producers (Abubakar and Abdulkadir, 2012). In Nigeria,agriculture was the dominant sector of the economy before independence;with groundnut cultivation as one of the vital areas of its economic built up (Ani et al, 2013). Emergence of petroleum products, poor....

For more Agricultural Engineering Projects click here
================================================================
Item Type: Project Material  |  Size: 127 pages  |  Chapters: 1-5
Format: MS Word  |  Delivery: Within 30Mins.
================================================================

Share:

Search for your topic here

See full list of Project Topics under your Department Here!

Featured Post

HOW TO WRITE A RESEARCH HYPOTHESIS

A hypothesis is a description of a pattern in nature or an explanation about some real-world phenomenon that can be tested through observ...

Popular Posts